Up to top level
AO15   AO16   AO17   AO18   Backgrounds   Calibration   Conference   Data   Docs   EPICMOS   EPICpn   Feedback   Gallery   Misc   OM   Pending   PhD_Theses   Publications   RGS   RadMonitor   SAS_Hardware   SAS_WS   SASv16.0   SASv16.0_Installation   SASv16.1   SASv16.1_Installation   SASv17.0   SASv17.0_Installation   SciSim   Simulators_other   Suggestions   Trash   Visibility   XMM-bouncing   XMM-news   XRPS   XSA   esas   incoming  

Logged in as guest

Viewing AO15/77444
Full headers

From: "Jelle Kaastra" <J.S.Kaastra@sron.nl>
Subject: Re: RPS form AO15: multiple TOO & joint observations
Compose reply
Download message
Move To:
0 replies:
0 followups:

Private message: yes  no

Notes:

Notification:


Date: Wed, 23 Sep 2015 17:53:18 +0200
From: "Jelle Kaastra" <J.S.Kaastra@sron.nl>
To: "Pedro M. Rodriguez Pascual" <xmmhelp@sciops.esa.int>
Subject: Re: RPS form AO15: multiple TOO & joint observations
thanks!

Jelle 
 
>>> "Pedro M. Rodriguez Pascual" <xmmhelp@sciops.esa.int>
9/23/2015 16:45 >>> 
Dear Jelle, 

please, mark as Joint Proposal: YES only the first observation (the one with the
requested XMM time) and fill in here the details of the other facilities. In all
other observations where XMM exposure time is set to zero you should also set
Joint Proposal: NO . 

Pedro


> Full_Name: Jelle Kaastra
> Submission from: (NULL) (192.87.213.35)
> 
> 
> I try to prepare an RPS form with multiple TOO targets, of which only one
will
> be triggered/observed. According to the new instructions, I need to specify
the
> XMM exposure only for the first potential target, and can keep it zero for
> subsequent targets. That part works fine. However, I also request joint
> observations with another facility. If I fill in zero exposure time for the
> joint facility for the subsequent targets, I get a complaint at the verify
stage
> that zero exposure is not allowed for the joint facility; however, if I
fill
in
> the exposure time for each target, the total exposure for the joint
facility
> appearing on the RPS form is too high, namely the number of targets times
the
> individual exposure time, rather than 1 x the individual exposure time. Is
there
> a solution to this problem, and what do you recommend to do?
> 
> 

This message and any attachments are intended for the use of the addressee or
addressees only.
The unauthorised disclosure, use, dissemination or copying (either in whole or
in part) of its
content is not permitted.
If you received this message in error, please notify the sender and delete it
from your system.
Emails can be altered and their integrity cannot be guaranteed by the sender.

Please consider the environment before printing this email.




Up to top level
AO15   AO16   AO17   AO18   Backgrounds   Calibration   Conference   Data   Docs   EPICMOS   EPICpn   Feedback   Gallery   Misc   OM   Pending   PhD_Theses   Publications   RGS   RadMonitor   SAS_Hardware   SAS_WS   SASv16.0   SASv16.0_Installation   SASv16.1   SASv16.1_Installation   SASv17.0   SASv17.0_Installation   SciSim   Simulators_other   Suggestions   Trash   Visibility   XMM-bouncing   XMM-news   XRPS   XSA   esas   incoming  

Logged in as guest


Please make your (short) question the subject of your request!


Web interface using JitterBug ... back to the XMM home page